Edgetech Edge Banding Spare Parts

Edgetech edge bander parts and listed dimensions

The Edgetech collection includes parts for different stations: upper pressure wheels, an end-trim wheel, a band pulling roller, a lower chain block and a glue-level sensor. Product names may include Edgetech dimensions or a general description such as universal. These words identify the listing; they do not promise fit for a particular machine configuration. The live list may also show another brand reference, such as a Homag 8 glue-level sensor. Do not assume every item in the collection was made for Edgetech. Compare the exact model and serial number, unit, part code and dimensions before choosing a replacement. If the old part has no readable code, use mounting photos and caliper measurements to identify candidate listings.

Upper pressure wheels: size, bearing and hub

Entries such as the Edgetech 70 by 25 by 17 mm upper pressure wheel and a universal 60 by 22 by 25 mm help distinguish products at first glance. Confirm dimension order in the product page, then record outside diameter, working width, shaft or bearing bore, hub thickness, shoulder profile and any Teflon or elastomer surface. The wheel may sit above a pressure station or on a side carrier; the mounting axis, free rotation and pressure arrangement affect selection. Check both faces of the old part for a code or direction mark. Record play, binding, cracks or a flattened surface. A wavy mark or slip on the panel edge can also relate to pressure height, speed, alignment or another component, so do not diagnose from one observation.

End-trim wheel and edge movement

The item named as an Edgetech 32 by 10 by 8 mm end-trim wheel is a listing whose dimensions and mounting should be confirmed. The word “wheel” does not mean every product is a cutting tool or works in the same way. Compare outside diameter, thickness, centre bore, material or surface, carrier body and mounting direction with the product image. Use the machine drawing to establish whether it belongs at the infeed or outfeed end-trim unit. If the part has no code, record its position and which edge of the processed panel shows the symptom. A trim mark or corner quality can also depend on unit setup, tool condition and feed direction. Follow the maker’s procedures for replacement and post-maintenance checks.

Band pulling roller and lower chain block

Products such as an Edgetech 60 by 30 by 16 mm band pulling roller and an 80 by 62 by 42 mm lower chain block perform different jobs and use different mounting geometries. For a roller, check outside diameter, width, hub, shaft, surface profile and direction of pull. For a block, check its three outside dimensions, thread, hole centres, chain or carrier fit and contact face. A roller and block with the same machine name are not interchangeable. The word “Edgetech” in a title does not provide a connection standard; confirm the machine serial number and parts catalogue. Wear may reduce the old block’s dimensions, so an intact item in the same row or a technical drawing can be a better comparison. Record the exact position, orientation and quantity on the carrier.

Glue-level sensor and other machine references

The live list may include a glue-level sensor named as Homag 8 and a sensor with a more general title. Its placement in the Edgetech collection does not establish direct fit with an Edgetech glue pot. The part code, sensing length, mounting thread, electrical connection, supply and controller input matter; the short “8” description does not specify every characteristic. Photograph the maker’s label, cable and connector and compare them with the machine wiring diagram or product documentation. Authorized staff should follow energy isolation, hot-surface and cooling procedures near heated adhesive equipment. A level alarm may relate to the sensor, cable, connector, PLC input or process residue. Collection copy does not identify the cause of the fault.

Document the Edgetech model and old component

Record the model on the nameplate, serial number, production year and any machine revisions. Identify the station where the part sits: pressure roller, band feed, lower chain, end trimming or glue tank. Copy every letter and digit in the part code. For an unmarked part, define dimensions by surface: for a wheel, outside diameter and total thickness; for a roller, shaft bore; for a block, hole centres; for a sensor, connection and body length. Photograph the mounting direction and nearby cables or mechanical components before removal. A drawing and item position in the parts catalogue make the comparison more useful when they match the product name. State if the measurement comes from a worn component and compare it with a sound counterpart where possible.

Symptoms, maintenance and part matching

If the edge material moves irregularly, do not immediately attribute the cause to the pulling roller. Roller pressure, tape path, adhesive condition, panel edge and transport speed can all matter. If a burr appears, record which end and travel direction are involved; pressure-wheel, end-trim, adjustment and tool condition may all need review. A broken or worn chain block should be considered together with the chain, connection and neighboring shoes. Keep the symptom time, machine alarm, last part change and photos in the maintenance record. Work on electrical connections, hot adhesive and moving mechanisms should follow the maker’s instructions and the site’s isolation procedures.

Related edge bander collections

Compare product families in [general edge bander parts](/en/collections/kenar-bantlama-parca), [Homag / Brandt](/en/collections/homag-brandt-kenar-bantlama-yedek-parca), [Biesse Akron](/en/collections/biesse-akron-kenar-bantlama-yedek-parca), [SCM Olimpic](/en/collections/scm-olimpic-kenar-bantlama-yedek-parca) and [Holzher Sprint](/en/collections/holzher-sprint-kenar-bantlama-yedek-parca). These collections help browse product names; a similar roller or sensor listed for another brand does not automatically fit Edgetech. Preserve the complete item name in a request and call out any other machine reference. Send the machine plate, OEM code, dimensions, drawing position, quantity and unresolved compatibility question together. Keeping an unverified product out of the confirmed spare-parts plan reduces confusion during a later purchasing cycle.

Code and station records for Edgetech items

For Edgetech spare-parts tracking, record the station as well as the wheel dimensions. An upper pressure wheel, band pulling roller and end-trim item may share a rotating shape but differ in diameter, contact face and mounting hub. For a universal 60 by 22 by 25 mm wheel or an Edgetech 70 by 25 by 17 mm wheel, verify the dimension order in the product detail; a purchase record without hub and shaft data is incomplete. Do not use “universal” to imply the same replacement across all Edgetech revisions. For a sensor, provide the manufacturer code, connector and cable photos in addition to the machine plate. Another-brand sensor or roller displayed on this page is not a cross-reference; leave that point explicit in purchasing notes.

Related parts collections

For items listed in Edgetech edge bander parts, compare related part types in edge bander spare parts · Biesse Akron edge bander parts · Homag / Brandt edge bander parts. Check the model, connection and full part reference separately for each product.